Effect of mineral composition and chemical activation of clay raw materials on the flexural strength of ceramic bodies
DOI:
https://doi.org/10.55225/sti.711Keywords:
clay minerals, flexural strength, modulus of rupture, sodium activation, smectite, kaolinite, illite, ceramic bodies, air-dried strength, clay minerals, flexural strength, modulus of rupture, sodium activation, smectite, kaolinite, illite, ceramic bodies, air-dried strengthAbstract
The mechanical strength of ceramic bodies in the air-dried state is one of the key technological parameters determining the course of forming, drying, and transport processes of ceramic green bodies. This study evaluates the influence of mineral composition and chemical activation of clay raw materials on the flexural strength of ceramic bodies, with particular emphasis on kaolinite, illitic clays, and smectite-rich raw materials. The effect of quartz sand addition and sodium activation (Na₂CO₃) on the mechanical properties of the specimens was also investigated.
Samples were prepared from KOC kaolin, Krakowiec clay, and bentonitic clay from the Bełchatów deposit, in both non-modified form and after sodium activation in the range of 3–10% Na₂CO₃. In the case of bentonitic bodies, quartz sand was added in amounts of 10–30%. Flexural strength was determined using the three-point bending method in the air-dried state and after drying at 105°C. In addition, the moisture content of the samples after drying was analyzed.
The obtained results demonstrated a significant influence of both mineral composition and chemical modification on the modulus of rupture values. The highest air-dried flexural strength was achieved for smectite-rich raw materials, whereas kaolin-based bodies exhibited the lowest binding capacity. Sodium activation resulted in a substantial improvement in the strength of all investigated ceramic bodies, although the effect strongly depended on the type of raw material and its particle size distribution. For bentonitic bodies containing 30% quartz sand, the highest modulus of rupture values were obtained with 10% Na₂CO₃ addition. Samples dried at 105°C exhibited higher strength values, which was attributed to closer packing of clay mineral layers and enhanced electrostatic interactions.
Downloads
References
Nait-Ali B, Alzina A, Lauro N, Smith DS. Perspectives in drying of ceramics. Open Ceramics. 2024;17:100554. https://doi.org/10.1016/j.oceram.2024.100554.
Dondi M, Raimondo M, Zanelli C. Clays and bodies for ceramic tiles: Reappraisal and technological classification. Applied Clay Science. 2014;96:91–109. https://doi.org/10.1016/j.clay.2014.01.013.
Lauro N, Oummadi S, Alzina A, Nait-Ali B, Smith DS. Computer model of drying behaviour of ceramic green bodies with particular reference to moisture content dependent properties. Journal of the European Ceramic Society. 2021;41(14):7321–7329. https://doi.org/10.1016/j.jeurceramsoc.2021.07.042.
Murzyn P, Brylska E, Stolecki J. Ceramiczne materiały budowlane: metody badań surowców i wyrobów. Kraków: Wydawnictwo AGH; 2014.
Vieira CMF, Sánchez R, Monteiro SN. Characteristics of clays and properties of building ceramics in the state of Rio de Janeiro, Brazil. Construction and Building Materials. 2008;22(5):781–787. https://doi.org/10.1016/j.conbuildmat.2007.01.006.
Wyszomirski P, Galos K. Surowce mineralne i chemiczne przemysłu ceramicznego. Kraków: Uczelniane Wydawnictwo Naukowo-Dydaktyczne AGH; 2007.
Kordek M. Technologia ceramiki. Cz. 1. Warszawa: Wydawnictwa Szkolne i Pedagogiczne; 1975.
Reed JS. Principles of Ceramics Processing. 2nd ed. New York: Wiley; 1995.
Carter CB, Norton MG. Ceramic Materials: Science and Engineering. New York: Springer; 2013.
Stoch L. Minerały ilaste. Warszawa: Wydawnictwa Geologiczne; 1974
Pisarczyk S. Gruntoznawstwo inżynierskie. Warszawa: Wydawnictwo Naukowe PWN; 2014.
Handke M. Krystalochemia krzemianów. Kraków: Wydawnictwo AGH; 2005.
Bergaya F, Lagaly G. Handbook of Clay Science. 2nd ed. Amsterdam: Elsevier; 2013.
Wilson, I. Applied Clay Mineralogy. Occurrences, processing and application of kaolins, bentonite, palygorskitesepiolite, and common clays. Clays and Clay Minerals. 2007;55:644–645. https://doi.org/10.1007/BF03406033.
Jasmund K, Lagaly G. Tonminerale und Tone. Darmstadt: Steinkopff Verlag; 1993.
Stoch L, Widaj J. Zależność wytrzymałości mechanicznej od uziarnienia surowców ilastych. Ceramika. 1970;2:45–56.
Vaculíková L, Plevová E, Vallová S, Koutník I. Characterization and differentiation of kaolinites from selected Czech deposits using infrared spectroscopy and differential thermal analysis. Acta Geodynamica Geomaterialia. 2011;8(1):59–67.
Śliwa T. Analiza odkształcania i pękania materiałów ilastych podczas suszenia konwekcyjnego. [Doctoral thesis]. Poznań: Politechnika Poznańska; 2014.
Bergaya F, Theng BKG, Lagaly G, editors. Handbook of Clay Science. Amsterdam–Tokyo: Elsevier; 2006.
Murray HH. Developments in Clay Science. Vol. 2. Amsterdam: Elsevier Science; 2007.
Ayadi A, Baklouti S, Kammoun A, Soro J. Study of clay’s mineralogy effect on mechanical properties of ceramic body using an experimental design. International Journal of Applied Ceramic Technology. 2021;19(3):1477–1489. https:doi.org/10.1111/ijac.13983.
Bernhardt M, Justnes H, Tellesbø H, Wiik K. The effect of additives on the properties of lightweight aggregates produced from clay. Cement and Concrete Composites. 2014;53:233–238. https://doi.org/10.1016/j.cemconcomp.2014.07.005.
Ayari F, Srasra E, Trabelsi-Ayadi M. Effect of exchangeable cations on the physicochemical properties of smectite. Surface Engineering and Applied Electrochemistry. 2007;43(5):369–378. https://doi.org/10.3103/S1068375507050110.
Slaný M, Jankovič L, Madejová J. Near-IR study of the impact of alkyl-ammonium and -phosphonium cations on the hydration of montmorillonite. Journal of Molecular Structure. 2022;1256:132568. https://doi.org/10.1016/j.molstruc.2022.132568.
Kłapyta Z, Żabiński W, editors. Sorbenty mineralne Polski. Kraków: Uczelniane Wydawnictwa Naukowo-Dydaktyczne AGH; 2008.
Galos K, editor. Surowce skalne: surowce ilaste. Kraków: Instytut Gospodarki Surowcami Mineralnymi i Energią Polskiej Akademii Nauk; 2004.
Panna W, Wyszomirski P, Motyka J. (2012). Bentonit z Kopernicy jako materiał do zastosowań hydroizolacyjnych. Zeszyty Naukowe IGSMiE PAN. 2012;83:131–145.
Panna W, Prosowicz G, Wyszomirski P. Ocena zawartości smektytu w niektórych ceramicznych surowcach ilastych na podstawie spektrofotometrycznych badań sorpcyjnych. Chemik. 2014;68(7):612–619.
Panna W, Wyszomirski P, Gasek K, Dudek R, Łabuz A. (2015). Hot stage microscopy in determining the suitability of selected clay rocks from South-Eastern Poland to manufacture lightweight aggregates. Cement, Wapno, Beton. 2015;20(2):79–87.
Komadel P. Chemically modified smectites. Clay Minerals. 2003;38(1):127–138. https://doi.org/10.1180/0009855
Oczoś K. Kształtowanie ceramicznych materiałów technicznych. Rzeszów: Oficyna Wydawnicza Politechniki Rzeszowskiej; 1996.
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Sebastian Dydo, Wojciech Panna, Jarosław Cyboroń, Radosław Madej

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.